Version notes
V 1.20 ****************
Added noise pip when line power off
Cal is now followed automatically by test
Cals and tests are stopped when entering into menu
alarms and alerts are now cleared from within their respective menus
Aes replaced with firmware on radio menu
Warnings from bulk writes fixed
Cal times changed, and frequency depends on temp
amps logging added
cable tests separated
added service limit menu
unstable probe alert
barometer alert
membrane temperature permeability adjustment added
worked probe voltage system a little
V 1.21 *************
buoy2 error stops #1 attempted fix
V 1.23 *************
Xtend mode is api only
added xtend reading feature separate from other
v 1.24 *************
fixed a few little bugs in buoy 2
added 5 second delay after commanded cal before test
v 1.25
worked with 512 adn 256
v 1.26
lowered battery to 21 volts charge
added 5 minute delay to aerator on without command
more amp averaging
v 1.28
added serial port viewer
added temp debugger in alerts
v1.30
fixed cable test problem?
v1.31
debug probe alert problems
added mixed radio
v1.32
averaged collar amps every second
v1.33
attempted fix on o2 inputs problem
v1.34
misc fixes
v1.35
Limit min cal
Log temp fix
required left and right arrows before advanced menu entry
v1.36
attempted emergency separation for two buoy systems
no cals below 50f, or 10c, and now only cal at 830 - 845
v1.37
allow fake DO for Gabe, along with time reset on cal/test -
use left and right arrows to enter.  Also, add to status report
v1.38
averaged barometer
v1.39
more averaging fixes
v1.40
fixed compensation
v1.41
fixed error with buoy 2 mv reading
v1.42
adjust overall gain
v1.43
adjust gain for 20x
v1.44
buoy 2 offset view fixed
v1.45
Extended fuse time, fixed on hand
v1.46
10 sec, 5 sec fuse times
v1.47
Acknowledge time write
v1.48
Change write time code for safety
v1.49
Update to allow 2.2k thermistor
v1.50
Added Pumpless option
Unstable test on cal only
Changed temperature taking at cal to end of test
v1.51
fixed cal LED error on dual buoy with reset
v1.52
separated do warnings between ponds
v1.53
moderate revamp including 16 bit crc on legacy mode api
all SET are now CRC'd instead of checksummed
Set, and time writes are screened for odd numbers.
v1.54
changed == to and in control process
v1.55
fixed number one aerator problem
v1.56
fixed serious negative positive DO on low readings
v1.57
fixed remote red flash
added remote indication
v1.58
Added KWH measurement
v1.59
Fixed Timer 1 and Timer 2 enabled write prevent
v1.60
lowered offset to 0.2 mv, and lowered cal time to 3 minutes
for pumpless systems
v1.61
fixed serial number
v1.62
changed high amp delay to 20 seconds
v1.63
Added co2 support, and water sensing
v1.64
Added unconnected amp sensor, or amp sensor misalignment detection.
v1.66
Corrected non saving breaker states
v1.67
Fixed error with amp sensor kicking in when low amp cut should have.
v1.68 
added time calibration, and added a few niceties for first time
v1.69
added red level set for LED, for orange color adjustment on new screens
v1.70 
corrected startup led viewing
v1.71
fixed non charging battery in pumpless mode
v1.72
updated starting led percent
v1.73
fixed amp sensor errors on dead battery
added thumb drive support
v1.74 
cleanup
v1.76 Fixed Xtend reader, post bootloader changeover
v1.77 Fixed aerator blipping due to emergency process
        Aerator on hand alert and startup.
v1.78 Fixed Co2 system with pumps not charging
v1.79 Changed D02enables to SystemType, also added extended testing mode, and lengthened testing pump breakers
v1.80.1 Put wait block for low power twilight re-startup zone.  Keypad lock after main mode fix.
        Clock alarm, with misc adjustments, no timers with clock alarm, etc.  Winter cal mode to 55f.
        110v back online holds original DO value prior to offline.
        Power off timer, if over 15 min, request new test immediately.
        Timers auto disable if aerators not attached to a buoy
v1.80.2 Added check for 9.5 Volts or greater before continuing program.
v1.80.3 radio handlers added for svc limits, and starting a new test or cal
        ask before shutting down aerators in IO test
        ask before stopping test or cal in progress, when entering do system
        cal and test run log
        slower charge blinking
v1.80.4 Seine mode
        IO test within maintenance mode
v1.80.5 Added split pond support with 2 modes, do/compare, and do/compare/timer
        removed ADC error
        Amp sensor calibration
        Removed adc error
        disable thumb drive with no logging
v1.90.0 Major renovation, pre 2.00.0 release
        Tractor style aeration with 2
        4 time periods
        User option for 5 and 6 timers, including split pond support
        Non disruptive timer entry
        Alarm alert log, and remove specific time alert/alarm
        Extended all structs to allow 12 aerators, and updated corresponding radio commands.

v1.90.1 Fixed startup issues, uninitialized timer 5 and 6, and CT rings.
v1.90.2 Resets overwrite fixed, and added tractor setpoints menu.
v1.90.3 Added multiple buoy support with low and int low do settings.
v1.90.4 System log transmitting
v1.90.5 Subtle radio transmission changes, plus add direct mode change
v1.91.3 Added support for aerator lock on, plus stepped off. fixed aerator emergency problem, possibly.
v1.91.6 Misc bug fixes.
v1.91.7 Corrected logging, added dual buoy.
        Added adjustable ntc support
v1.91.8 Fixed buoy 2 aerator on issue
v1.91.9 Added temperature adjustment
        Fixed Do control override issue on co2 + no pumps
        Add support for circulator reversed setpoints on buoy 2
v1.92.7 Changed logging to require minimum amperage
v1.92.8 Fixed up logging, added 5 second option, fixed MV to log through complete cycle
v1.92.9 Fixed 24 hr alert, was not operating above 25ppm and above 5 degree C
        Fixed system reset opposite from yes no.
v1.93.0 Changed EMFtime to 1 second, and added pre and post logging to system log
        Fixed resets while pumps running
        24 hour single anti wrap
        Added keypad lock
v1.93.4 Log seeding
v1.93.5 Probe sanity checks, larger buoy logs, buoy logs saved in different location.
        Shortened cal and test
V2.02.6 Power off detection, cal/test retries, new menu system, amp scaling, many changes
v2.03.1 Charge limiting to protect charge resistor from burning up
v2.03.3 Cal change excessive changes
v2.03.4 Corrected reverse compensation for cal change
v2.03.8 Calibration normalization centered at 25C, remote control work
v2.04.2 Battery fix, misc
v2.04.6 Probe unresponsive work
v2.04.7 Alternate aeration
v2.05.1 Global write fix for max mv
v2.05.2 Emergency aeration tweaks, fix aerator on hand
v2.05.4 Probe safety work, internal memory use fixes
v2.05.7 Temp range log limiting, Cal check adjustment
v2.06.0 DST fix, Log buoy amps to system log, Clear rtcc error on Time set
v2.06.1 Added aerator tag for thumb drive logging, reworked run without command
v2.06.3 Remote link colors on LED, Remote control time spacing, New test request if last sample too long, fix for delay after power outage.
v2.06.5 Changed defaults on new boxes, Different system logs for different clock errors
v2.06.6 XBEE read support on com1mixed
v2.06.8 HB20 support, amp sensor error delay, log aerator ma on sensor error, better sensor swap logging
v2.06.9 Xtend RN option
v2.07.0 Fix Pumpless errors
v2.07.1 Probe unresponsive exclusions by time window
v2.07.2 Remote amp sensor swap error fix, faster i2c, ram tuning.
v2.07.3 Spurious unknown alarm fix
v2.07.4 Reboot radio for Xtend 2003 errata, (aka Lee's catfish issue with needing pondside resets)
v2.07.4b Setup menu updates, LED levels for different screen boards.
v2.07.5 Watchdog ready firmware, stack dump filler, non watchdog bootloader warning on startup, 
        internal exception causes all red lights on face
v2.07.6 Change "slow rise" to "Dampened DO". Evening calibration at 22:00 after service.
        Battery checking, Battery alarm now based on battery health rather than voltage.
        Last aerator down alarm addition.
        High test pump amps self reset after 1 day
        NIMH compatible charging
v2.07.7 Spurious battery alarm fix for 2.07.6
v2.08.0	Battery work
v2.08.1 Battery level upped
v2.08.3 Battery alarms tweaked for spurious alarms, logs shortened to 8 days, maintenance mode sends unsolicited report
        Check HOA and cal/test on maintenance exit
v2.08.4 Fix long standing Rapid DO issue, Battery charging work. Single and double buoy pump states shown instead of numbers
        Battery logging
v2.08.5 Charger alarm work (unresolved issues)
v2.08.7 Support for i2c barometer
v2.09.0 Salinity support
v2.09.1 Allow greater than 50 amp setpoints
v2.09.2b Xtend RfMode, RfDelay read
v2.09.3 Daily week timer, 
v2.09.5 Service record support
v2.09.6 Repair emergency aeration issue introduced in 2.09.2
v2.09.8 Battery failing work on power blips, Aerator staging on enter svc mode, Buoy Calibration high fallback to highest
        Alarm/Alert buoy & aerator reset GUI info. DDO update from Fake DO entry.
v2.09.9 Interim install mode work
v2.10.0 Completed Install mode, shows as Maintenance in AerWare
v2.10.1 Removed Emergency aeration, Tractor aeration, added outbound on-hand aerator flags
        Rollover missing count, fix 1319 tracker Cal change excessive on request from maintenance exit.
        Asks about cal change after config import.
v2.10.2 Public Release.  Removed New_Status report, Removed Alternating aeration.
v2.10.3 Fix broken 4 day cal change excessive, broken since around 2.06.0
v2.10.4 Repair silent InstallMode issue, add some checks to maintenance/seine remote entry
v2.10.5 Removed Remote Maintenance mode
v2.10.6 Low Bromine alert inhibit after not testing for some time
v2.10.7 Better external command filtering, Time request to aerware, fix backup map error
        Repair Aeration not shutting off due to off timer not cleared
v2.11.0 Reverse RSSI reporting, sync support, new system log, system log remote line support.
        Re-work and add to probe unstable detections. Rise in post, cycling in test, fall in cal.
        Added soft detect of service for 4 day cal spurious alerts
        Added reverse Xtend RSSI reporting
        Full syslog read, one line per request
        Changed Min bromine check to 4.0
        Scaled Unstable ranges to 40.0mV center
        Changed Min Max temp table
        Added RSSI to face upper left corner in Single buoy mode
        Added remote Amp offset adjust by turning on Sensor breaker 
v2.11.1 Fix low threshold false Probe unstable @ Run
v2.11.2 Fix Non working RM420, broken after 2.10.5
v2.11.3 Fix Probe unstable false flags
v2.11.4 Fix probe unstable @ run on flatlines
v2.11.5 Probe Unstable changes, change hours from 6 to 10 or 11, twice on @ run